Toyota Venza: Vehicle Stability Control System
- Precaution
- Parts Location
- System Description
- System Diagram
- How To Proceed With Troubleshooting
- Calibration
- Check For Intermittent Problems
- Test Mode Procedure
- Problem Symptoms Table
- Terminals Of Ecu
- Diagnosis System
- Dtc Check / Clear
- Freeze Frame Data
- Fail-safe Chart
- Data List / Active Test
- Diagnostic Trouble Code Chart
- Steering Angle Sensor Initialization Incomplete (C1439/31,C1445/31)
- Performance Decline of Brake Function (C1441)
- Yaw Rate Sensor Output Malfunction (C1448/98)
- Control Module Communication Bus OFF (U0073/94,U0100/65,U0123/62,U0124/95,U0126/63)
- Stop Light Control Relay Malfunction (C1380/64)
- Skid Control ECU Malfunction (C1300/62)
- Brake Pedal Load Sensing Switch (C1267/67)
- ECU Version Miss Match (C1288/88)
- Open in Stop Light Switch Circuit (C1249/49)
- Master Cylinder Pressure Sensor Malfunction (C1246/46,C1281/81)
- Speed Sensor Rotor Faulty (C1237/37,C1275/75-C1278/78)
- Low Battery Positive Voltage or Abnormally High Battery Positive Voltage (C1241/41)
- Steering Angle Sensor Circuit Malfunction (C1231/31)
- Malfunction in Deceleration Sensor (C0365/28,C1234/34,C1245/32,C1245/45)
- Engine Control System Malfunction (C1201/51)
- Open or Short Circuit in ABS Solenoid Relay Circuit (C0278/11)
- Open or Short Circuit in ABS Motor Relay Circuit (C0273/13)
- SFR Solenoid Circuit (C0226/21,C0236/22,C0246/23,C0256/24,C1225/25-C1228/28)
- ABS Control System Malfunction (43)
- Rear Speed Sensor RH Circuit (C0210/33,C0215/34,C1273/73,C1274/74,C1332/38,C1333/39)
- Front Speed Sensor RH Circuit (C0200/31,C0205/32,C1271/71,C1272/72,C1330/35,C1331/36)
- ABS Warning Light Remains ON
- ABS Warning Light does not Come ON
- Brake Warning Light Remains ON
- Brake Warning Light does not Come ON
- TRAC OFF Indicator Light Remains ON
- TRAC OFF Indicator Light does not Come ON
- VSC OFF Indicator Light Remains ON
- VSC OFF Indicator Light does not Come ON
- Slip Indicator Light does not Come ON
- Slip Indicator Light Remains ON
- TC and CG Terminal Circuit
- TS and CG Terminal Circuit
Removal
REMOVAL
CAUTION / NOTICE / HINT
NOTICE:
Do not remove the steering angle sensor from the spiral cable.
HINT:
The steering angle sensor is a component of the spiral with sensor cable sub-assembly. ...
Precaution
PRECAUTION
1. PRECAUTION FOR DISCONNECTING THE BATTERY CABLE
NOTICE:
When disconnecting the cable from the negative (-) battery terminal, initialize
the following systems after the cable is recon ...
Other materials about Toyota Venza:
Headlight (HI-BEAM) Circuit
DESCRIPTION
for Halogen Headlight:
The main body ECU (driver side junction block assembly) controls the
high beam headlights.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system bef ...
SRS Warning Light Remains ON
DESCRIPTION
The SRS warning light is located on the combination meter assembly.
When the SRS is normal, the SRS warning light comes on for approximately 6 seconds
after the ignition switch is turned from off to ON, and then goes off automatically.
If ther ...
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Navigation System / Trouble
Codes.
(e) Check for DTCs (See page ).
...
0.1608