Toyota Venza: Lighting (ext)
- Afs Ecu
- Automatic Light Control Sensor
- Door Mirror Foot Light
- Fog Light Assembly
- Hazard Warning Switch
- Headlight Assembly
- Headlight Dimmer Switch
- Headlight Leveling Ecu
- Height Control Sensor
- High Intensity Discharge Headlight Bulb
- High Mounted Stop Light Assembly
- License Plate Light Assembly
- Lighting System
- Parts Location
- Precaution
- System Description
- System Diagram
- How To Proceed With Troubleshooting
- Operation Check
- Customize Parameters
- Initialization
- Problem Symptoms Table
- Terminals Of Ecu
- Diagnosis System
- Dtc Check / Clear
- Fail-safe Chart
- Freeze Frame Data
- Data List / Active Test
- Diagnostic Trouble Code Chart
- Vehicle Specifications have not been Stored (B2451)
- Lost Communication with Automatic High Beam Sensor (B2432)
- Initialization has not been Performed (B2450)
- HL AutoLeveling ECU Failure (B2420)
- Rear Height Control Sensor (B241A)
- Height Control Sensor Malfunction (B2416)
- Vehicle Speed Sensor Malfunction (B2415)
- Height Control Sensor Data Out of Range When Initializing (B2452)
- Variation Error (B2453)
- Light Sensor Circuit Malfunction (B1244)
- Lost Communication with ECM (U0101,U0073,U0126,U0129,U0142,U0182,U1000)
- Automatic High Beam Mirror (B124A)
- Automatic High Beam System (B124B)
- Automatic High Beam Camera (B124C)
- Lost Communication with AFS LIN (B124D)
- Steering Position Sensor Malfunction (B2414)
- Headlight Relay Circuit
- Headlight Solenoid Circuit
- Daytime Running Light Relay Circuit
- Headlight (HI-BEAM) Circuit
- Front Fog Light Circuit
- Headlight Signal Circuit
- Light Control Switch Circuit
- Door Mirror Foot Light Circuit
- Parking Brake Switch Circuit
- Taillight Relay Circuit
- Headlight Beam Level Control Actuator Circuit
- Headlight Leveling ECU Power Source Circuit
- Indicator Circuit
- Speed Signal Circuit
- Inner Rear View Mirror Power Source Circuit
- LVL Terminal Circuit
- Diagnosis Circuit
- Rear Combination Light Assembly
- Rear Light Assembly
- Relay
- Side Turn Signal Light Assembly
- Stop Light Switch
- Turn Signal Flasher Assembly
Relay
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT HORN RELAY (ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
(a) Remove the engine room junction block assembly from the engine ro ...
Afs Ecu
Components
COMPONENTS
ILLUSTRATION
Installation
INSTALLATION
PROCEDURE
1. INSTALL AFS ECU
(a) Engage the guide.
(b) Install the ...
Other materials about Toyota Venza:
Installation
INSTALLATION
PROCEDURE
1. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
(a) Install the No. 3 parking brake cable assembly with the bolt and 4 nuts.
Torque:
Nut (A) :
5.4 N·m {55 kgf·cm, 48 in·lbf}
Nut (B) :
6.0 N·m {61 kgf·cm, 53 in·lbf}
Bolt ...
Customizing the features by using the multi-information display (vehicles with
TFT type multi-information display)
Press the “SETUP” button while the vehicle is stopped.
The “Custom Settings” screen is displayed on the multi-information display.
If left idle for approximately 10 seconds, the display will revert to the previous
screen.
Select the setting yo ...
Trailer towing
Your vehicle is designed primarily as a passenger-and-load-carrying vehicle.
Towing a trailer can have an adverse impact on handling, performance, braking, durability,
and fuel consumption. For your safety and the safety of others, you must not overload
...
0.1377