REGISTRATION
PROCEDURE
1. DESCRIPTION OF CODE REGISTRATION
HINT:
The key has 2 codes: the key code (immobiliser code) and the wireless code. Both
of these codes need to be registered. For the wireless code registration procedures,
refer to Wireless Door Lock Control System (See page
).
(a) When adding master keys (Additional registration):
(1) Register the key code (immobiliser code) in the transponder key ECU assembly.
Target ECU |
Refer to |
---|---|
Transponder key ECU assembly |
Procedure "B" |
(b) When replacing the transponder key ECU assembly (New registration):
(1) Register the key code (immobiliser code) in the new transponder key ECU assembly.
Target ECU |
Refer to |
---|---|
Transponder key ECU assembly |
Procedure "A" |
(2) Register the ECU communication ID between the new transponder key ECU assembly and the ECM.
Target ECU |
Refer to |
---|---|
ECM |
Procedure "E" |
(c) When replacing the ECM:
(1) Register the ECU communication ID between the transponder key ECU assembly and the new ECM.
Target ECU |
Refer to |
---|---|
Transponder key ECU assembly |
Procedure "F" |
(d) When replacing the transponder key ECU assembly and the ECM:
(1) Register the key codes (immobiliser codes) in the new transponder key ECU assembly.
Target ECU |
Refer to |
---|---|
Transponder key ECU assembly |
Procedure "A" |
(2) Register the ECU communication ID between the new transponder key ECU assembly and the new ECM.
Target ECU |
Refer to |
---|---|
Transponder key ECU assembly |
Procedure "F" |
(e) When erasing key codes:
(1) Erasing all of the key codes except the master key.
Target ECU |
Refer to |
---|---|
Transponder key ECU assembly |
Procedure "C" |
(2) Erasing all of the key codes.
Target ECU |
Refer to |
---|---|
Transponder key ECU assembly |
Procedure "D" |
2. KEY REGISTRATION
(a) New key code registration (Procedure "A"):
NOTICE:
Make sure that no key codes are registered in the transponder key ECU assembly.
HINT:
Procedure |
Security Indicator Light Condition |
---|---|
1. Start |
Blinking HINT: Until first key is inserted |
2. Insert the master key into the ignition key cylinder. |
ON |
3. Techstream operation Enter the following menus: Body Electrical / Immobiliser / Utility / Key Registration HINT: After completing the above operation, proceed to the next step in accordance with the prompts on the Techstream screen. |
OFF for 1 second and then ON |
4. Remove the key and then select Next on the Techstream. |
ON |
5. Insert the master key to be registered and then select Next on the Techstream. |
OFF for 1 second and then ON |
6. Remove the key and then select Next on the Techstream. |
ON |
7. Remove the key. |
Blinking |
8. End (Procedure "E") |
HINT:
(b) Finish the automatic key code registration mode. The automatic key code registration mode can be forced to end when at least 1 key code (immobiliser code) for the master key has been registered.
HINT:
Follow the instruction on the Techstream screen to end new key code registration mode.
3. REGISTRATION OF ADDITIONAL KEY
(a) Additional registration (Procedure "B"):
HINT:
NOTICE:
When the ignition key cylinder has been replaced, locking and unlocking doors are possible with the new master key transmitter module (removed from the original master key). However, the new master key will not be able to lock and unlock doors through the door key cylinder. Keep the original master key. If the battery in the new master key transmitter module fails, the original master key can be used to lock and unlock doors through the door key cylinder.
Additional Registration
Procedure |
Time to Complete Operation |
Security Indicator Light Condition |
---|---|---|
1. Start |
- |
Blinking HINT: Until first key is inserted |
2. Insert the already registered master key into the ignition key cylinder and turn the ignition switch to ON. |
- |
OFF |
3. Techstream operation Enter the following menus: Body Electrical / Immobiliser / Utility / Key Registration HINT: After completing the above operation, proceed to the next step in accordance with the prompts on the Techstream screen. |
Within 120 sec. |
ON |
4. Remove the master key. |
Within 20 sec. HINT: After the Techstream instruction |
ON |
5. Insert the key to be registered in the ignition key cylinder. |
Within 10 sec. |
Blinking |
6. Wait for 60 sec. after the key is registered. HINT: The security indicator light goes off. |
- |
OFF |
7. Remove the key. |
- |
Blinking |
8. End |
HINT:
4. ERASURE OF KEY CODE
(a) Key code erasure (Procedure "C"):
HINT:
Procedure |
Time to Complete Operation |
Security Indicator Light Condition |
---|---|---|
1. Start |
- |
Blinking HINT: Until first key is inserted |
2. Insert the already registered master key in the ignition key cylinder and turn the ignition switch to ON. |
- |
OFF |
3. Techstream operation Enter the following menus: Body Electrical / Immobiliser / Utility / Transponder Code Erasure HINT: After completing the above operation, proceed to the next step in accordance with the prompts on the Techstream screen. |
Within 120 sec. |
ON for 1 sec. then OFF |
4. Remove the master key. |
Within 10 sec. HINT: After the Techstream instruction |
ON |
5. End |
HINT:
(b) All key code erasure (Procedure "D"):
HINT:
Procedure |
Time to Complete Operation |
Security Indicator Light Condition |
---|---|---|
1. Start |
- |
Blinking |
2. Insert previously registered master key or unregistered key into ignition key cylinder and turn ignition switch to ON. |
Within 10 min. |
ON or OFF |
3. Using TIS, confirm that user and vehicle match. |
||
4. Techstream operation Enter the following menus: Body Electrical / Immobiliser / Utility / Transponder Code Erasure HINT: After completing the above operation, proceed to the next step in accordance with the prompts on the Techstream screen. |
Within 15 min. |
ON for 1 sec. then OFF |
5. Completion of erasure of all key codes is displayed. |
Within 10 sec. HINT: After the Techstream instruction |
ON |
6. End |
HINT:
5. ECU COMMUNICATION ID REGISTRATION
(a) ECU communication ID registration (Procedure "E"):
NOTICE:
- Using the Techstream
- Disconnecting the battery for 30 seconds
(1) Using SST, connect terminals TC and CG of the DLC3.
SST: 09843-18040
(2) Turn the ignition switch to ON and leave the vehicle as is for 30 minutes.
HINT:
Do not start the engine.
(3) Check that the engine starts.
(b) ECU communication ID registration (Procedure "F"):
NOTICE:
The ECU communication ID should be registered when the ECM and transponder key ECU assembly are replaced or when the ECM only is replaced in order to match the ECU communication ID.
ECU Communication ID Registration
Procedure |
Security Indicator Light Condition |
---|---|
1. Start |
OFF |
2. Insert an already registered key into the ignition key cylinder. |
|
3. Start the engine. |
|
4. Check that the engine starts and stays on for more than 3 seconds. |
|
5. End |
Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
Using the Techstream to read the Data List allows the values or states of switches,
sensors, actuators and other items to be read without removing any parts. This non-intrusive
inspection can be very useful because in ...
Bottle holders
► For front seats
► For rear seats
NOTICE
- Items that should not be stowed in the bottle holders
Put the cap on before stowing a bottle. Do not place open bottles in the bottle
holders, or glasses and paper cups containing liquid. ...
Driver Side Door ECU Communication Stop (B2321)
DESCRIPTION
This DTC is stored when LIN communication between the power window regulator
motor assembly (for driver side) and main body ECU (driver side junction block assembly)
stops for more than 10 seconds.
DTC No.
DTC Detection ...