Toyota Venza: Data List / Active Test

Toyota Venza Service Manual / Theft Deterrent / Keyless Entry / Theft Deterrent System(w/ Smart Key System) / Data List / Active Test

DATA LIST / ACTIVE TEST

1. DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Main Body / Data List.

(e) According to the display on the Techstream, read the Data List.

Main Body

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
D Door Courtesy SW	D door courtesy switch/ON or OFF	ON: Driver side door open OFF: Driver side door closed	-
P Door Courtesy SW	P door courtesy switch/ON or OFF	ON: Front passenger side door open OFF: Front passenger side door closed	-
RR Door Courtesy SW	Rear right door courtesy switch/ON or OFF	ON: Rear right door open OFF: Rear right door closed	-
RL Door Courtesy SW	Rear left door courtesy switch/ON or OFF	ON: Rear left door open OFF: Rear left door closed	-
Back Door Courtesy SW	Back door courtesy switch/ON or OFF	ON: Back door open OFF: Back door closed	-
D-Door Lock Pos SW	Driver door lock position switch/ON or OFF	ON: Driver door unlocked OFF: Driver door locked	-
P-Door Lock Pos SW	Passenger door lock position switch/ON or OFF	ON: Passenger door unlocked OFF: Passenger door locked	-
Back Door Open	Back door lock / Permit or Prohibit	Permit: Back door unlocked Prohibit: Back door locked	-
RR-Door Lock Pos SW	Rear right door lock position switch/ON or OFF	ON: Rear right door unlocked OFF: Rear right door locked	-
RL-Door Lock Pos SW	Rear left door lock position switch/ON or OFF	ON: Rear left door unlocked OFF: Rear left door locked	-
Passive Mode (Security system)	Passive mode/ON or OFF	ON: Passive mode on OFF: Passive mode off	-
Warning by Horn	Warning by horn/ON or OFF	ON: Vehicle horn(s) sound during alarm sounding state OFF: Vehicle horn(s) do no sound during alarm sounding state	-
Entry Delay	Entry delay time during passive mode	0 s: Entry delay time 0 sec. 14 s: Entry delay time 14 sec. 30 s: Entry delay time 30 sec.	-

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. The Data List can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Main Body / Active Test.

(e) According to the display on the Techstream, perform the Active Test.

Main Body

Tester Display	Test Part	Control Range	Diagnostic Note
Hazard	Hazard warning lights	ON / OFF	-
Vehicle Horn	Vehicle horns	ON / OFF	-
Security Indicator	Security indicator	ON / OFF	-
Security Horn	Security horn	ON / OFF	-

Terminals Of Ecu

TERMINALS OF ECU 1. CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY) (a) Disconnect the main body ECU (driver side junction block assembly) connectors. (b) Measure the resistance and vol ...

Diagnosis System

DIAGNOSIS SYSTEM 1. DESCRIPTION The ECU stores trouble codes when trouble occurs on the vehicle. The diagnostic system allows for reading of the trouble codes from the DLC3. Use the Techstream to ...

Other materials about Toyota Venza:

Power Source Mode does not Change to ON (ACC)
DESCRIPTION When the engine switch is pushed with the electrical key in the cabin, the power management control ECU receives signals to change the power source mode. HINT: To allow use of the Techstream to inspect the push-button start function when the ...

Speed Sensor Rotor Faulty (C1237/37,C1275/75-C1278/78)
DESCRIPTION The skid control ECU measures the speed of each wheel by receiving signals from the speed sensor. These signals are used for recognizing that all four wheels are operating properly. Therefore, all wheel signals must be equal. DTCs C1275/75 to ...

Terminals Of Ecu
TERMINALS OF ECU 1. POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (a) Disconnect the I6 power window regulator master switch assembly connector. (b) Measure the voltage and resistance according to the value(s) in the table below. HINT: Measure the val ...