Toyota Venza: Data List / Active Test

Toyota Venza Service Manual / Seat / Front Power Seat Control System(w/ Memory) / Data List / Active Test

DATA LIST / ACTIVE TEST

1. DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Mirror L / Data List.

(e) Read the Data List according to the display on the Techstream.

Mirror L

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Seat Memory Switch1	M1 switch / ON or OFF	ON: M1 switch on OFF: M1 switch off	-
Seat Memory Switch2	M2 switch / ON or OFF	ON: M2 switch on OFF: M2 switch off	-
Seat Memory Switch3*	M3 switch / ON or OFF	ON: M3 switch on OFF: M3 switch off	Not applicable
Seat Memory Set SW	SET switch / ON or OFF	ON: SET switch on OFF: SET switch off	-
+B Voltage Input Value	Power supply for outer mirror control ECU assembly LH / MIN: 0 V, MAX: 19.98 V	Within range from 11 to 14 V	-

*: Although the item is displayed on the Techstream, it is not applicable to this vehicle.

(f) Enter the following menus: Body Electrical / Driver Seat / Data List.

(g) Read the Data List according to the display on the Techstream.

Driver Seat

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Reclining Rear	Reclining switch signal (Rearward) / ON or OFF	ON: Reclining switch (Rearward) on OFF: Reclining switch (Rearward) off	-
Reclining Front	Reclining switch signal (Forward) / ON or OFF	ON: Reclining switch (Forward) on OFF: Reclining switch (Forward) off	-
Front Vertical Down	Front vertical switch signal (Downward) / ON or OFF	ON: Front vertical switch (Downward) on OFF: Front vertical switch (Downward) off	-
Front Vertical Up	Front vertical switch signal (Upward) / ON or OFF	ON: Front vertical switch (Upward) on OFF: Front vertical switch (Upward) off	-
Lifter Switch Down	Lifter switch signal (Downward) / ON or OFF	ON: Lifter switch (Downward) on OFF: Lifter switch (Downward) off	-
Lifter Switch Up	Lifter switch signal (Upward) / ON or OFF	ON: Lifter switch (Upward) on OFF: Lifter switch (Upward) off	-
Slide Rear	Slide switch signal (Rearward) / ON or OFF	ON: Slide switch (Rearward) on OFF: Slide switch (Rearward) off	-
Slide Front	Slide switch signal (Forward) / ON or OFF	ON: Slide switch (Forward) on OFF: Slide switch (Forward) off	-
Seat Memory No1	Seat position memorized with M1 switch / Mem or Not Mem	Mem: Memorized Not Mem: Not memorized	-
Seat Memory No2	Seat position memorized with M2 switch / Mem or Not Mem	Mem: Memorized Not Mem: Not memorized	-
Seat Memory No3*	Seat position memorized with M3 switch / Mem or Not Mem	Mem: Memorized Not Mem: Not memorized	Not applicable
Ignition Switch	Communication state of ignition switch signal / ON or OFF	ON: Ignition switch ON signal received OFF: Ignition switch off signal not received	-
P Switch	Park state signal / ON or OFF	ON: Shift lever in P OFF: Shift lever in a position other than P	-
Parking Brake SW	Parking brake switch status / ON or OFF	ON: Parking brake applied OFF: Parking brake released	-
Vehicle Speed	Vehicle speed data / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)	Actual vehicle speed	-
Power Voltage	Power supply for position control ECU and switch assembly / min: 0.95 V, max: 20.84 V	Within range from 11 V to 14 V	-
Slide Position	Seat sliding position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Reclining Position	Seat reclining position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Front Vertical Position	Seat front vertical position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Lifter Position	Seat lifter position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Slide Pos Mem No1	Seat slide position memorized with M1 switch / min: 0000, max: 65535	Within range from 0000 to 65535	-
Reclining Pos Mem No1	Seat reclining position memorized with M1 switch / min: 0000, max: 65535	Within range from 0000 to 65535	-
Frnt Vrtcl Pos Mem No1	Front vertical position memorized with M1 switch / min: 0000, max: 65535	Within range from 0000 to 65535	-
Lifter Pos Mem No1	Lifter position memorized with M1 switch / min: 0000, max: 65535	Within range from 0000 to 65535	-
Slide Pos Mem No2	Seat slide position memorized with M2 switch / min: 0000, max: 65535	Within range from 0000 to 65535	-
Reclining Pos Mem No2	Seat reclining position memorized with M2 switch / min: 0000, max: 65535	Within range from 0000 to 65535	-
Frnt Vrtcl Pos Mem No2	Front vertical position memorized with M2 switch / min: 0000, max: 65535	Within range from 0000 to 65535	-
Lifter Pos Mem No2	Lifter position memorized with M2 switch / min: 0000, max: 65535	Within range from 0000 to 65535	-
Slide Pos Mem No3*	Seat slide position memorized with M3 switch / min: 0000, max: 65535	Within range from 0000 to 65535	Not applicable
Reclining Pos Mem No3*	Seat reclining position memorized with M3 switch / min: 0000, max: 65535	Within range from 0000 to 65535	Not applicable
Frnt Vrtcl Pos Mem No3*	Front vertical position memorized with M3 switch / min: 0000, max: 65535	Within range from 0000 to 65535	Not applicable
Lifter Pos Mem No3*	Lifter position memorized with M3 switch / min: 0000, max: 65535	Within range from 0000 to 65535	Not applicable
Headrest Switch UP*	Headrest switch signal (UP) / ON or OFF	ON: Headrest switch (UP) on OFF: Headrest switch (UP) off	Not applicable
Headrest Switch Down*	Headrest switch signal (Down) / ON or OFF	ON: Headrest switch (Down) on OFF: Headrest switch (Down) off	Not applicable
Motor Status	State of slide motor control / STANDBY, MOVING, LOCK	STANDBY: Slide motor idle MOVING: Slide motor moving LOCK: Slide motor locked	-
Lifter Initialize Flag	Seat lifter limit position memory / ON or OFF	ON: Memorized OFF: Not memorized	-
Front Vertical Init Flag	Seat front vertical limit position memory / ON or OFF	ON: Memorized OFF: Not memorized	-
Reclining Position Init Flg	Seat reclining limit position memory / ON or OFF	ON: Memorized OFF: Not memorized	-
Slide Position Init Flag	Seat slide limit position memory / ON or OFF	ON: Memorized OFF: Not memorized	-
Slide Position Front Limit	Seat sliding position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Slide Position Rear Limit	Seat slide position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Reclining Position Front Limit	Seat reclining position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Reclining Position Rear Limit	Seat reclining position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Front Vertical UP Limit	Seat front vertical position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Front Vertical Down Limit	Seat front vertical position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Lifter Position UP Limit	Seat lifter position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Lifter Position Down Limit	Seat lifter position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Shift P sw(PMN)*	Park state signal / ON or OFF	ON: Shift lever in P OFF: Shift lever in a position other than P	Not applicable
Memory Button Buzzer Request	Driver seat buzzer request display / OFF, MOVE, REGISTRY, CANCEL, REG NG, REG WAIT	OFF: Buzzer does not sound MOVE: Request to sound buzzer when starting memory replay REGISTRY: Request to sound buzzer when starting memory registration CANCEL: Request to sound buzzer when canceling memory call registration REG NG: Request to sound buzzer when memory call registration not possible REG WAIT: Request to sound buzzer when starting memory call cabin scan	-
Driver Seat Request Command	Driver seat operation request received / OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET	OFF: No instruction MEMORY: Request to memorize MEM MOV: Request to recall memory MEM SOD: Request to replay RET MOV: Request to return AWY MOV: Request to move away AWY SOD: Request to recall away position memory MEM AWY: Request to recall memorized position of seatback MEM RET: Request to restore seatback to memorized position	-
Driver Seat POS REQ	Seat memory switch operation value / OFF, MEM1, MEM2, MEM3, DRV1, DRV2* or DRV3*	OFF: No operation MEM1: M1 switch operation status MEM2: M2 switch operation status MEM3: M3 switch operation status* DRV1: Other 1 operation status* DRV2: Other 2 operation status* DRV3: Other 3 operation status*	-
Away Move Range Scale	The seat travel distance for the power easy access system / NONE, SMALL, STANDARD or LONG	NONE: Seat travel distance none SMALL: Seat travel distance short STANDARD: Seat travel distance normal LONG: Seat travel distance long	-
Return Move	Return function / NOT AVL or AVAIL	NOT AVL: Not available AVAIL: Available	-
Return & Away Function	Return & away function / NOT AVL or AVAIL	NOT AVL: Not available AVAIL: Available	-
Driver Seat Buckle SW	Driver seat belt buckle switch / ON or OFF	ON: Driver seat belt fastened OFF: Driver seat belt unfastened	-
Return Position	Return position / min: 0000, max: 65535	Within range from 0000 to 65535	-
Sensor Power Voltage	Sensor Power Voltage / min: 0 V, max: 19.89 V	Within range from 11 to 14 V	-
Number of Trouble Codes	Number of trouble codes / min.: 0 or max.: 255	Number of DTCs will be displayed	-

*: Although the item is displayed on the Techstream, it is not applicable to this vehicle.

(h) Enter the following menus: Body Electrical / Main Body / Data List.

(i) Read the Data List according to the display on the Techstream.

Main Body

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
D Door Courtesy SW	Front door courtesy light switch assembly LH signal / ON or OFF	ON: Driver door open OFF: Driver door closed	-
Door Lock SW-Lock	Door control switch (power window regulator master switch assembly) lock signal / ON or OFF	ON: Lock side of door control switch (power window regulator master switch assembly) pushed OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed	-
Door Lock SW-Unlock	Door control switch (power window regulator master switch assembly) unlock signal / ON or OFF	ON: Unlock side of door control switch (power window regulator master switch assembly) pushed OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed	-
Mem SW No. w/KeyID1	Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3*	NONE: No switches linked with key ID1 MEM SW1: M1 switch linked with key ID1 MEM SW2: M2 switch linked with key ID1 MEM SW3: M3 switch linked with key ID1*	-
Mem SW No. w/KeyID2	Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3*	NONE: No switches linked with key ID2 MEM SW1: M1 switch linked with key ID2 MEM SW2: M2 switch linked with key ID2 MEM SW3: M3 switch linked with key ID2*	-
Mem SW No. w/KeyID3	Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3*	NONE: No switches linked with key ID3 MEM SW1: M1 switch linked with key ID3 MEM SW2: M2 switch linked with key ID3 MEM SW3: M3 switch linked with key ID3*	-
Mem SW No. w/KeyID4	Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3*	NONE: No switches linked with key ID4 MEM SW1: M1 switch linked with key ID4 MEM SW2: M2 switch linked with key ID4 MEM SW3: M3 switch linked with key ID4*	-
Mem SW No. w/KeyID5	Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3*	NONE: No switches linked with key ID5 MEM SW1: M1 switch linked with key ID5 MEM SW2: M2 switch linked with key ID5 MEM SW3: M3 switch linked with key ID5*	-
Mem SW No. w/KeyID6	Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3*	NONE: No switches linked with key ID6 MEM SW1: M1 switch linked with key ID6 MEM SW2: M2 switch linked with key ID6 MEM SW3: M3 switch linked with key ID6*	-
Mem SW No. w/KeyID7	Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3*	NONE: No switches linked with key ID7 MEM SW1: M1 switch linked with key ID7 MEM SW2: M2 switch linked with key ID7 MEM SW3: M3 switch linked with key ID7*	-
Driver Seat Memory1	Seat position memorized with M1 switch / OFF or ON	OFF: Not memorized ON: Memorized	-
Driver Seat Memory2	Seat position memorized with M2 switch / OFF or ON	OFF: Not memorized ON: Memorized	-
Driver Seat Memory3*	Seat position memorized with M3 switch / OFF or ON	OFF: Not memorized ON: Memorized	Not applicable

*: Although the item is displayed on the Techstream, it is not applicable to this vehicle.

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Driver Seat / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Driver Seat

Tester Display	Test Part	Control Range	Diagnostic Note
Seat Reclining	Seat reclining operation	OFF/Front/Rear	-
Front Vertical Operation	Seat front vertical operation	OFF/Up/Down	-
Lifter Operation	Seat lifter operation	OFF/Up/Down	-
Seat Slide Operation	Seat slide operation	OFF/Front/Rear	-
Buzzer	Buzzer operation	OFF/ON	-

Dtc Check / Clear

DTC CHECK / CLEAR 1. CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Driver Seat ...

Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART If a trouble code is displayed during the DTC check, inspect the trouble areas listed for that code. For details of the code, refer to the ''See page'' ...

Other materials about Toyota Venza:

Relay
On-vehicle Inspection ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT IG2 RELAY (a) Remove the IG2 relay from the relay block. (b) Measure the resistance according to the value(s) in the table below. Standard Resistance: Te ...

CD Sound Skips
PROCEDURE 1. CHECK CD (a) Check that the CD is not deformed or cracked. OK: No deformation or cracks on the CD NG END (CD IS FAULTY) ...

Removal
REMOVAL PROCEDURE 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ). 2. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (w/o Seat Heater Syste ...