Toyota Venza: Reassembly

REASSEMBLY

PROCEDURE

1. REPAIR INSTRUCTION

2. INSTALL REAR DOOR OUTSIDE MOULDING

3. INSTALL REAR DOOR LOWER OUTSIDE STRIPE

4. INSTALL NO. 2 BLACK OUT TAPE

5. INSTALL REAR DOOR OUTSIDE STRIPE

6. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING

7. INSTALL REAR DOOR REAR WINDOW FRAME MOULDING

8. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

9. INSTALL REAR DOOR BELT MOULDING

10. INSTALL REAR DOOR PANEL PROTECTOR

(a) Engage the 6 clips and install the rear door panel protector.

11. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

(a) Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.

(b) Engage the door handle nut and claw.

(c) Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.

Torque:

4.0 N·m {41 kgf·cm, 35 in·lbf}

12. INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

(a) Engage the 2 claws and install the rear door rear outside handle pad.

13. INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

(a) Engage the 3 claws to install the rear door front outside handle pad.

14. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

(a) Insert the front end of the rear door outside handle assembly into the rear door outside handle frame. NOTICE: If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.

(b) Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.

(c) Move the lever back in the direction indicated by the arrow in the illustration to lock the door outside handle assembly.

15. INSTALL REAR DOOR OUTSIDE HANDLE COVER

(a) Engage the claw and install the rear door outside handle cover.

(b) Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

Torque:

4.0 N·m {41 kgf·cm, 35 in·lbf}

16. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

(a) Install the rear door inside locking cable assembly.

(b) Engage the 3 claws.

17. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

(a) Install the rear door lock remote control cable assembly.

(b) Engage the claw.

18. INSTALL REAR DOOR LOCK ASSEMBLY

(a) Apply MP grease to the sliding parts of the rear door lock assembly.

(b) Install a new door lock wiring harness seal to the rear door lock assembly.

(c) Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.

(d) Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

(e) Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

(f) Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.

Torque:

5.0 N·m {51 kgf·cm, 44 in·lbf}

19. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.

(a) Using a T25 "TORX" socket wrench, install the rear power window regulator motor assembly with the 3 screws. Torque: 5.4 N·m {55 kgf·cm, 48 in·lbf} HINT: A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

20. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY

(a) Apply MP grease to the sliding parts of the rear door window regulator assembly.

(b) Install the temporary bolt to the rear door window regulator assembly.

(c) Temporarily install the rear door window regulator assembly. Text in Illustration *1 Temporary Bolt

(d) Tighten the temporary bolt and 3 bolts.

HINT:

Tighten the bolts and the nuts in the order shown in the illustration.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

(e) Install the rear door window regulator assembly with the 2 bolts. Torque: 8.0 N·m {82 kgf·cm, 71 in·lbf}

21. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

(a) Connect the cable to the negative (-) battery terminal and the rear power window regulator motor connector.

(b) Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

(c) Disconnect the power window regulator switch assembly and the rear power window regulator motor connector.

(d) Disconnect the cable from the negative (-) battery terminal.

(e) Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as indicated by the arrows, in the order shown in the illustration.

(f) Install the rear door glass sub-assembly with the 2 bolts. Torque: 8.0 N·m {82 kgf·cm, 71 in·lbf}

(g) Install the hole plug.

22. INSTALL REAR DOOR REAR GUIDE SEAL

(a) Install the rear door rear guide seal with the 2 screws.

23. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

(a) Install the temporary bolt to the rear door window division bar sub-assembly.

(b) Temporarily install the rear door window division bar sub-assembly. Text in Illustration *1 Temporary Bolt

(c) Install the 2 screws.

(d) Tighten the temporary bolt and bolt to install the rear door window division bar sub-assembly.

(e) Install the hole plug.

24. INSTALL REAR DOOR GLASS RUN

(a) Install the rear door glass run.

25. INSTALL REAR DOOR WEATHERSTRIP

(a) Engage the 21 clips and install the rear door weatherstrip.

26. INSTALL REAR DOOR CHECK ASSEMBLY

(a) Apply MP grease to the sliding areas of the rear door check assembly.

(b) Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

(c) Install the rear door check assembly with the bolt and 2 nuts. Torque: Bolt : 29 N·m {296 kgf·cm, 21 ft·lbf} Nut : 5.5 N·m {56 kgf·cm, 49 in·lbf}

27. INSTALL REAR DOOR SERVICE HOLE COVER

(a) Apply butyl tape to the rear door panel.

(b) Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

(c) Attach the rear door service hole cover according to the reference points on the rear door panel.

NOTICE:

Securely install the rear door service hole cover preventing wrinkles and air bubbles.

(d) Connect the 2 connectors.

(e) Engage the 2 clamps.

28. INSTALL REAR DOOR INSIDE PANEL REINFORCE SUB-ASSEMBLY

(a) Install the rear door inside panel reinforce sub-assembly with the 4 screws.

29. INSTALL REAR SPEAKER ASSEMBLY

30. INSTALL REAR DOOR FRAME GARNISH

(a) Engage the clip to install a new rear door frame garnish.

31. INSTALL REAR NO. 2 SPEAKER ASSEMBLY (for 13 Speakers)

32. INSTALL REAR SPEAKER BRACKET (for 13 Speakers)

33. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

(a) Engage the 7 claws and install the rear door inner glass weatherstrip to the rear door trim board sub-assembly as shown in the illustration.

34. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

(a) Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.

(b) Engage the 2 claws and install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.

35. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

(a) for 13 Speakers:

(1) Connect the connector.

(b) Engage the 8 clips and install the rear door trim board sub-assembly.

(c) Install the 2 screws.

36. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

(a) Connect the connector.

(b) Engage the 2 clips and 5 claws, and install the rear power window regulator switch assembly with rear door armrest base panel.

37. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

(a) Engage the 3 claws and install the rear door inside handle bezel plug.

38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).

39. INITIALIZE POWER WINDOW CONTROL SYSTEM

(See page )