To ensure correct programming into the HomeLink®, install a new battery in the hand-held transmitter prior to programming. Failure to install a new battery into the hand-held transmitter will affect both the range and accuracy of the HomeLink® in your vehicle.
The battery side of the hand-held transmitter must be pointed away from the HomeLink® during the programming process.
The HomeLink® compatible transceiver in your vehicle has 3 buttons which can be programmed to operate 3 different devices. Refer to the programming method below appropriate for the device.
1. Indicator
2. Buttons
- Programming HomeLink®
Point the remote control transmitter for the device 1 to 3 in. (25 to 75 mm) from the HomeLink® buttons.
Keep the HomeLink® indicator light in view while programming.
Press and hold one of the HomeLink® buttons and the transmitter button. When the HomeLink® indicator light changes from a slow to a rapid flash within 20 seconds, you can release both buttons.
Test the HomeLink® operation by pressing the newly programmed button.
If a HomeLink® button has been programmed for a garage door, check to see if the garage door opens and closes. If the garage door does not operate, see if your remote control transmitter is of the rolling code type. Press and hold the programmed HomeLink® button. The remote control transmitter is of the rolling code type if the HomeLink® indicator light flashes rapidly for 2 seconds and then remains lit. If your transmitter is of the rolling code type, proceed to the heading “Programming a rolling code system”.
Repeat the steps above to program
another device for each of the remaining HomeLink® buttons.
- Programming a rolling code system
If your device is rolling code equipped, follow the steps under the heading “Programming HomeLink®” before proceeding with the steps listed below.
Locate the learn button on the ceiling
mounted garage door opener motor. The exact location and color of the button may
vary by brand of garage door opener motor.
Refer to the operation manual supplied with the garage door opener motor for the location of the learn button.
Press the learn button.
Following this step, you have 30 seconds in which to initiate step 3 below.
Press and hold the vehicle’s programmed
HomeLink® button for 2 seconds and release it. Repeat this step once again. The
garage door may open.
If the garage door opens, the programming process is complete. If the door does not open, press and release the button a third time.
This third press and release will complete the programming process by opening the garage door.
The ceiling mounted garage door opener motor should now recognize the HomeLink® signal and operate the garage door.
Repeat the steps above to program
another rolling code system for any of the remaining HomeLink® buttons.
- Programming an entry gate (for U.S.A. owners)/Programming all devices in the Canadian market
Place your transmitter 1 to 3 in.
(25 to 75 mm) away from the surface of the HomeLink®.
Keep the HomeLink® indicator light in view while programming.
Press and hold the selected HomeLink®
button.
Repeatedly press and release (cycle)
the device’s remote control button for two seconds each until step 4 is completed.
When the indicator light on the
HomeLink® compatible transceiver starts to flash rapidly, release the buttons.
Test the operation of the HomeLink®
by pressing the newly programmed button. Check to see if the gate/device operates
correctly.
Repeat the steps above to program
another device for each of the remaining HomeLink® buttons.
- Programming other device
s To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance.
- Reprogramming a button
The individual HomeLink® buttons cannot be erased but can be reprogrammed. To reprogram a button, follow the “Programming” instructions.
Accelerator Pedal
Components
COMPONENTS
ILLUSTRATION
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT ACCELERATOR PEDAL SENSOR ASSEMBLY
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) En ...
Reassembly
REASSEMBLY
CAUTION / NOTICE / HINT
HINT:
Perform "Inspection After Repair" after replacing the cylinder head sub-assembly
(See page ).
PROCEDURE
1. INSTALL SPARK PLUG TUBE
HINT:
When using a new cylinder head, the spark plug tubes must be r ...
Light bulbs
You may replace the following bulbs yourself. The difficulty level of replacement
varies depending on the bulb. If necessary bulb replacement seems difficult to perform,
contact your Toyota dealer.
For more information about replacing other light bulbs, c ...