Toyota Venza manuals

Toyota Venza: Maintenance requirements

To ensure safe and economical driving, day-to-day care and regular maintenance is essential. It is the owner’s responsibility to perform regular checks. Toyota recommends the following maintenance.

 - General maintenance

Should be performed on a daily basis. This can be done by yourself or by a Toyota dealer.

- Scheduled maintenance

Should be performed at specified intervals according to the maintenance schedule.

For details about maintenance items and schedules, refer to the “Scheduled Maintenance Guide”, “Owner’s Manual Supplement”.

- Do-it-yourself maintenance

You can perform some maintenance procedures yourself.

Please be aware that do-it-yourself maintenance may affect warranty coverage.

The use of Toyota Repair Manuals is recommended.

For details about warranty coverage, see the separate “Owner’s Warranty Information Booklet”, “Owner’s Manual Supplement”.

 - Repair and replacement

It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the warranty coverage.

 - Reset the maintenance data (U.S.A. only)

After the required maintenance is preformed according to the maintenance schedule, please reset the maintenance data.

To reset the data, follow the procedures described below:

Switch the display to the trip meter
A when the engine is running.

Vehicles with smart key system:


Turn the “ENGINE START STOP” switch off.

Vehicles without smart key system:

Turn the engine switch to the “LOCK” position.

Vehicles with smart key system:


While pressing the trip meter reset button, set the “ENGINE START STOP” switch to IGNITION ON mode (but do not start the engine because otherwise the reset mode will be canceled). Continue to press and hold the trip meter reset button until the trip meter displays “000000”.

Vehicles without smart key system:

While pressing the trip meter reset button, set the engine switch to “ON” position (but do not start the engine because otherwise the reset mode will be canceled). Continue to press and hold the trip meter reset button until the trip meter displays “000000”.

 - Allow inspection and repairs to be performed by a Toyota dealer

• Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.

• Keep a copy of the repair order. It proves that the maintenance that has been performed is under warranty coverage. If any problem should arise while your vehicle is under warranty, your Toyota dealer will promptly take care of it.

CAUTION

 - Warning in handling of battery, oils, fuels, and fluids

• Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.

• Oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Avoid exposure and wash any affected area immediately.

• Battery posts, terminals and related accessories contain lead and lead compounds which are known to cause brain damage. Wash your hands after handling.

Maintenance
...

General maintenance
Listed below are the general maintenance items that should be performed at the intervals specified in the “Scheduled Maintenance Guide”, “Owner’s Manual Supplement”. It is recommended th ...

Other materials about Toyota Venza:

Certification ECU Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area Certification ECU Communication Stop Mode "Smart Access/Smart Key/Wireless Tuner" is not displayed on "CAN Bus Check&q ...

Sending Malfunction (Navigation to APGS) (U0073,U0100,U0140,U0155)
DESCRIPTION These DTCs are stored when a malfunction occurs in the CAN communication circuit. DTC No. DTC Detection Condition Trouble Area U0073 CAN bus connection error CAN communicatio ...

On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. CHECK POWER SOURCE MODE CHANGE FUNCTION (a) Check the function of the engine switch. (1) Check that power source mode changes in accordance with the conditions of the shift position and brake pedal. Brake Pe ...

© 2016-2024 Copyright www.tovenza.com

0.1224