DIAGNOSTIC TROUBLE CODE CHART
Main Body ECU (Driver Side junction Block Assembly)|
DTC Code |
Detection Item |
Trouble Area |
See page |
|---|---|---|---|
|
B1206 |
P/W Master Switch Communication Stop |
1. Multiplex network master switch assembly 2. Main body ECU (Driver side junction block assembly) 3. Wire harness or connector 4. ECU-B NO. 2 fuse |
|
|
B124D |
Lost Communication with AFS LIN |
1. Inner rear view mirror assembly 2. Wire harness or connector 3. AFS ECU (headlight swivel ECU assembly) |
|
|
B1273 |
Sliding Roof ECU Communication Stop |
1. Sliding roof ECU (Sliding roof drive gear assembly) 2. Main body ECU (Driver side junction block assembly) 3. Wire harness or connector 4. S/R fuse |
|
|
B2287 |
LIN Communication Master Malfunction |
1. Multiplex network master switch assembly 2. Main body ECU (Driver side junction block assembly) 3. Wire harness or connector |
|
|
B2321 |
Driver Side Door ECU Communication Stop |
1. Power window regulator motor assembly (for Driver side) 2. Main body ECU (Driver side junction block assembly) 3. Multiplex network master switch assembly 4. Wire harness or connector 5. FL DOOR fuse |
|
|
B2322 |
Front Passenger Side Door ECU Communication Stop |
1. Power window regulator motor assembly (for Front passenger side) 2. Main body ECU (Driver side junction block assembly) 3. Wire harness or connector 4. FR DOOR fuse |
|
|
B2323 |
Rear Door RH ECU Communication Stop |
1. Power window regulator motor assembly (for Rear RH side) 2. Main body ECU (Driver side junction block assembly) 3. Wire harness or connector 4. RR DOOR fuse |
|
|
B2324 |
Rear Door LH ECU Communication Stop |
1. Power window regulator motor assembly (for Rear LH side) 2. Main body ECU (Driver side junction block assembly) 3. Wire harness or connector 4. RL DOOR fuse |
|
|
B2325 |
LIN Communication Bus Malfunction |
1. Power window regulator motor assembly (for Driver side) 2. Power window regulator motor assembly (for Front passenger side) 3. Power window regulator motor assembly (for Rear RH side) 4. Power window regulator motor assembly (for Rear LH side) 5. Multiplex network master switch assembly 6. Sliding roof ECU (Sliding roof drive gear assembly) 7. Main body ECU (Driver side junction block assembly) 8. Wire harness or connector |
|
|
DTC Code |
Detection Item |
Trouble Area |
See page |
|---|---|---|---|
|
B2785 |
Communication Malfunction between ECUs Connected by LIN |
1. Certification ECU (Smart key ECU assembly) 2. Power source control ECU (Power management control computer assembly) 3. Steering lock ECU (Steering lock actuator assembly) 4. Wire harness or connector |
|
|
B2786 |
No Response from Steering Lock ECU |
1. Steering lock ECU (Steering lock actuator assembly) 2. Certification ECU (Smart key ECU assembly) 3. Wire harness or connector 4. STR LOCK fuse |
|
|
B278C |
Lost Communication with Power Source Control |
1. Power source control ECU (Power management control computer assembly) 2. Certification ECU (Smart key ECU assembly) 3. Wire harness or connector 4. AM2 fuse |
|
|
DTC Code |
Detection Item |
Trouble Area |
See page |
|---|---|---|---|
|
B2432 |
Lost Communication with Automatic High Beam Sensor |
1. Inner rear view mirror assembly 2. Wire harness or connector 3. AFS ECU (headlight swivel ECU assembly) |
|
Lost Communication with Power Source Control (B278C)
No Response from Steering Lock ECU (B2786)Fuel Receiver Gauge Malfunction
DESCRIPTION
The meter CPU uses the fuel sender gauge assembly to determine the level
of the fuel in the fuel tank. The resistance of the fuel sender gauge will
vary between approximately 7.5 Ω with the float at the full position, and
185 Î ...
Inspection
INSPECTION
PROCEDURE
1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)
(a) The L position of the left/right adjustment switch: Measure the resistance
according to the value(s) in the table below.
Standard Resistance (for Left Side):
Tes ...
Terminals Of Ecu
TERMINALS OF ECU
1. CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
(a) Disconnect the P4 ECU connector.
(b) Measure the resistance and voltage according to the value(s) in the table
below.
HINT:
Measure the values on the wire harness si ...