Toyota Venza: Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Enter the following menus:
(1) for Combination Meter: Body Electrical / Combination Meter / Data List.
(2) for ABS/VSC/TRAC: Chassis / ABS/VSC/TRAC / Data List.
(3) for Engine and ECT: Powertrain / Engine and ECT / Data List.
(g) Check the values by referring to the table below.
Combination Meter|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Tail Cancel Switch |
Tail cancel switch/OFF or ON |
OFF: Light control rheostat knob not turned fully clockwise |
- |
|
ON: Light control rheostat knob turned fully clockwise |
- |
||
|
ODO/TRIP Change SW |
ODO/TRIP switch/OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
- |
||
|
Vehicle Speed Meter |
Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) |
Almost the same as actual vehicle speed (Speedometer tester) |
- |
|
Engine Rpm |
Engine speed/Min.: 0 rpm, Max.: 12750 rpm |
600 to 700 rpm (When idling) |
- |
|
Coolant Temperature |
Engine coolant temperature/Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) |
After warming up: 80 to 100°C (176 to 212°F) |
- |
|
Washer Switch |
Washer fluid level warning switch /OFF or ON |
OFF: Washer fluid level is not low |
- |
|
ON: Washer fluid level is low |
- |
||
|
Timer Switch M on Combination Meter |
Drive monitor switch (US/M M*1 or SETUP*2 switch)/OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
|||
|
Timer Switch H on Combination Meter |
Drive monitor switch (RESET H*1 or SELECT RESET*2 switch)/OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
|||
|
Drive Monitor Reset SW |
Drive monitor switch signal (INFO CLOCK*1 or INFO*2 switch)/OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
|||
|
+B Voltage Value |
Battery voltage/Min.: 0 V, Max.: 25.5 V |
11 to 14 V |
- |
|
Fuel Input |
Fuel input signal/Min.: 0, Max.: 127.5 |
Current fuel level displayed |
Unit: Liter |
|
Ambient Temperature |
Outside temperature/Min.: -40°C (-40°F), Max.: 50°C (122°F) |
Almost the same as actual outside temperature |
The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F) |
|
Rheostat value |
Light Control Rheostat/Min.: 0%, Max.: 100% |
Light control rheostat switch Dark (0%) → Bright (100%) |
- |
|
Quantity of Outside Light |
Quantity of outside light/Min.: 0%, Max.: 100% |
Outside light is Dark (0%) → Bright (100%) |
- |
|
Key Remind Sound |
The cycle of the key reminder warning buzzer/Large, Medium or Small |
Cycle of the key reminder warning buzzer is Large, Medium or Small |
The current setting of the cycle of the key reminder warning buzzer is displayed. |
|
Key Remind Volume |
The volume of the key reminder warning buzzer/Fast, Normal or Slow |
Volume of the key reminder warning buzzer is Fast, Normal or Slow |
The current setting of the volume of the key reminder warning buzzer is displayed. |
|
Driver Side Seatbelt Warning Buzzer |
The condition of the driver side seat belt warning buzzer/OFF or ON |
ON: Driver side seat belt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when driver side seat belt unfastened |
The customized setting of the driver side seat belt warning buzzer is displayed |
|
OFF: Driver side seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when driver side seat belt unfastened |
|||
|
P-Seatbelt Warning Buzzer |
The condition of the front passenger side seat belt warning buzzer/OFF or ON |
ON: Front passenger side seat belt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when front passenger side seat belt unfastened |
The customized setting of the front passenger side seat belt warning buzzer is displayed |
|
OFF: Front passenger side seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when front passenger side seat belt unfastened |
|||
|
Number of Trouble Code |
The number of the DTC which is currently output |
0 |
- |
- *1: w/o Multi-information Display
- *2: w/ Multi-information Display
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
FR Wheel Speed |
Vehicle speed/Min.: 0 mph (0 km/h), Max.: 202 mph (326 km/h) |
Almost the same as actual vehicle speed (Speedometer tester) |
- |
|
FL Wheel Speed |
Vehicle speed/Min.: 0 mph (0 km/h), Max.: 202 mph (326 km/h) |
Almost the same as actual vehicle speed (Speedometer tester) |
- |
|
RR Wheel Speed |
Vehicle speed/Min.: 0 mph (0 km/h), Max.: 202 mph (326 km/h) |
Almost the same as actual vehicle speed (Speedometer tester) |
- |
|
RL Wheel Speed |
Vehicle speed/Min.: 0 mph (0 km/h), Max.: 202 mph (326 km/h) |
Almost the same as actual vehicle speed (Speedometer tester) |
- |
|
Vehicle Speed |
Vehicle speed/Min.: 0 mph (0 km/h), Max.: 202 mph (326 km/h) |
Almost the same as actual vehicle speed (Speedometer tester) |
- |
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Engine Speed |
Vehicle speed/Min.: 0 rpm, Max.: 16383 rpm |
600 to 700 rpm (When idling) |
- |
|
Coolant Temp |
Engine coolant temperature/Min.: -40°C (-40°F), Max.: 215°C (419°F) |
80 to 100°C (176 to 212°F): After warming up |
|
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Engine Speed |
Vehicle speed/Min.: 0 rpm, Max.: 16383 rpm |
600 to 700 rpm (When idling) |
- |
|
Coolant Temp |
Engine coolant temperature/Min.: -40°C (-40°F), Max.: 140°C (284°F) |
80 to 100°C (176 to 212°F): After warming up |
|
2. ACTIVE TEST
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(e) Check the operation by referring to the table below.
Combination Meter|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Speed Meter Operation |
Speedometer |
0, 40, 80, 120, 160, 200 km/h |
Confirm that the vehicle is stopped with the engine idling |
|
Acceptable range (km/h): [Control range → Speedometer display]
|
|||
|
Tacho Meter Operation |
Tachometer |
0, 1000, 2000, 3000, 4000, 5000, 6000, 7000 (rpm) |
Confirm that the vehicle is stopped with the engine idling |
|
Fuel Meter Operation |
Fuel receiver gauge |
EMPTY, 1/2, FULL |
Confirm that the vehicle is stopped with the engine idling |
|
A/T Indicator Operation 1 |
A/T shift indicator light (D, P, N. R, 4, 3, 2, L) |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
A/T Indicator Operation 2 |
A/T gear range indicator light (S, 6, 5) |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Lamp Airbag |
SRS warning light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Lamp Doors All Open |
Door indicator light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Front Passenger Side Seat Belt |
Front passenger side seat belt warning light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Driver Side Seat Belt |
Driver side seat belt warning light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Lamp ABS |
ABS warning light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Lamp Charge |
Charge warning light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Lamp Slip |
Slip indicator light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Lamp Beam |
High beam indicator light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Lamp Tail |
Tail indicator light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Lamp Fr FOG |
Front fog indicator light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Lamp Washer |
Washer fluid level warning light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Lamp Fuel |
Fuel level warning light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
VSC TRC Indicator |
Trac off indicator light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
4WD Warning Indicator*1 |
AWD warning indicator light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Tire Pressure Warning System |
Tire pressure warning light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Lamp Cruise |
Cruise indicator light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. Lamp Brake |
Brake warning light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. EPS |
EPS warning light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. KEY*3 |
Key indicator light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Master Warning*4 |
Master warning light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. SET |
Set indicator light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Indicat. VSC OFF |
VSC OFF indicator light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Automatic High Beam Indicator*2 |
Automatic high beam indicator light |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Water Temperature Meter Operation |
Engine coolant temperature receiver gauge |
Low, Normal, High |
Confirm that the vehicle is stopped with the engine idling |
|
Meter Display 1 |
Combination meter display (0, 1, 2, 3, 4, 5, 6, All) |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
|
Meter Display 2 |
Combination meter display (7, 8, 9) |
OFF or ON |
Confirm that the vehicle is stopped with the engine idling |
- *1: for AWD
- *2: w/ Automatic High Beam System
- *3: w/ Smart Key System
- *4: w/ Multi-information Display
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON and turn the Techstream on.
(c) Enter the following menus: Body Electrical / Trouble Codes ...
Fail-safe Chart
FAIL-SAFE CHART
Engine Coolant Temperature Gauge
Condition
Response
Recovery
Engine coolant temperature data is interrupted for 3 seconds.
...
Other materials about Toyota Venza:
Lost Communication with ECM (U0101,U0073,U0126,U0129,U0142,U0182,U1000)
DESCRIPTION
The DTCs are stored when the CAN communication system is malfunctioning.
DTC No.
DTC Detection Condition
Trouble Area
U0101
Lost communication with ECM
CAN communication syst ...
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use the following procedure to troubleshoot the key reminder warning
system.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROUGHT TO WORKSHOP
NEXT
...
No Sound can be Heard from Speakers
PROCEDURE
1.
CHECK AUDIO SETTINGS
(a) In sound setting mode, set volume, fader and balance to the initial values
and check that the sound is normal.
OK:
Audio system returns to normal.
HINT:
Sound quality adjustment mea ...
0.113